OpenBCM V1.07b6_bn2 (Linux)

Packet Radio Mailbox

FFLB0X

[[FFL-B0X]]

 Login: GAST





  
NL2SNE > TECHNI   22.06.09 17:54l 153 Lines 7242 Bytes #999 (0) @ WW
BID : 54209_CB9SNK
Read: GAST
Subj: K rogerbeep scematic.
Path: FFLB0X<DBO595<BX0RBL<DP0RBL<DBX563<CB0BGR<CB9SNK
Sent: 090621/1304Z @:CB9SNK.FRL.NLD.EU #:54209 [Sneek] Sneek $:54209_CB9SNK
From: NL2SNE@CB9SNK.FRL.NLD.EU
To  : TECHNI@WW


** Message generated by:
** FSG WinFBB Message Editor v2.0b (c)2000 FSG's JO1HDV
  --------------------------------------------------------


By G8MNY                                    (Updated Jan 09)
(8 Bit ASCII Graphics use code page 437 or 850)
This is an add on for anyone who wants an optional automatic CW "K" PIP tone
after each over. This used to be popular for short SSB overs under QSB/QRM
conditions like during contests, as it stops doubleing etc. & in my experiance
actually speeds up the contact with less contest oriantated stations.

Other Morse letters are possible but not exceeding 9 time slots that this
circuit gives, see REPEATERS below.

It has an internal PP3 battery to run the unit while on Tx, which is very
lightly trickle charged from the PTT line on Rx to maintain the battery.

Features include an LED showing PIP tone is armed (lit during Tx overs) & a "K"
LED showing the K leaving.

 ÚÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÂÄÄÄ´>ÃÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄ¿ MIC RIG
===    Hold hi \³        R7       ³         ³   D8  _³_    _³_PIP  ³ PTT PTT
 ³C1   for K  T2ÃÄÄÄÄ¿    ³      R14        ³    D9 /_\  <-/_\LED1 ³  ³   ÃÄÄ¿
R1            e/³    R6  === C4   ³        R15       ÃÄÄÄÄÄÄ)ÄÄÄÄÄÄ)ÄÄ)ÄÄÄ´ R25
 ³            ³      ³    ³       ³ +9V     ³        ³     R22   ONÀo/o oÄÙ  ³
 ÃÄR3ÄÂÄÄÄÄÄÄÄÁÄÂÄÄÄÄ)ÄÄÄÄ)ÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄ)ÄÄÄÂÄÄÄÄ)ÄÄÄÂÄÄÁÄÄÂÄÄÄÄo/o oOFF ³
 ³  ³/e         ³    ³    ³                 ³ ³/e    ³  +³C10  ³  SW1 ³      ³
 ÃÄÄ´T1         ³    ÃÄÄÄÄ)ÄÄÄÄÄÄR16ÄÄÄÄÄÄÄÄÁÄ´T5    ³  ===    ³      ÃÄ´<ÃÄÄÙ
 ³  ³\          ³    ³Long³Start K  ___IC2    ³\ PTT ³  _³_    ³     +³ D10
 ³    ³PTT      ³    ³    ÃÄÄÄÄÄÄÄij1  A\4011   ³O/P ³         ³  9v ÄÁÄ
===   ³Start    ³    ³   R8        ³2   3)o¿   R17 ³/    ÚÄÄÄÄÄ´ Batt Â
 ³C2  ³Reset    ³    ³   _³_ ÚÄR10ij____/  ³    ÃÄÄ´T6  _³_    ³  PP3 ³
 ³    ³         ³    ³       ÃÄR11ÂÄÄÄÄÄÄÄÄÙ    ³  ³\e  \_/->K ³     _³_
 ³    ³  C3     ³    ³      ===   ³ ____  CW   R18   ³   ³LED2 ³
 ³    ³ Ú´ÃÂÄÄÄÄ)ÄÄÄÄ)ÄÄR5ÄÄÄ´C5  ó5  B\ Clock ÃÄÄÄÄÙ  R23    ³
 ³    ³ ³  ³ÚÄÄÄÁÄÄÄ¿³       ³    ³³6   4)o¿   _³_       ³     ³
R2    ³ ³  À³14 16 3³Ù D1    ³27HzÀ³____/  ³           ³/      ³
_³_   ³ ÃÄÄij13    2³´>ÃÄ¿   ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÙ   ÚÄÄÄÄÄÄÄ´T4     ³
      ÃÄ)ÄÄij15    4³Ä´>ô K _._    ___+14     ³       ³\e     ³
      ³ ³   ³      7³´>ÃÄÅÄÄÄÄÄÄÄÄij8  C\     R19       _³_    ³
     R4 ³   ³ IC1  1³Ä´>ô Morse   ³9  10)o¿   ³             ³/
      ³ ³   ³4017  6³´>ÃÄ´   ÚÄR12ij____/  ³   ÃÄR20ÄÂÄR21ÄÂÄ´T3
      ³ ³   ³      9³Ä´>ô   ÃÄR13ÂÄÄÄÄÄÄÄÄÙ   ³    ===C7  ³ ³\e
      ³ ³   ³  8  11³´>ÃÄ´  ===   ³ ___-7  AF  ³     ÀÄÄÄÄÄ)ÄÄÄ´    C9
      ³ ³   ÀÄÄÂÄÄÄÄÙ D7 ³   ³C6  ó12 D\  Osc ³    AF    === VR1<ÄÄ´ÃÄR24Ä>MIC
      ³ ³      ³        R9   ³    ³³13 11)oÂÄÄÄÙ  Filter C8³   ³ O/P
      ÀÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÂÄÄÙ   ³1kHzÀ³____/  ³               ÃÄÄÄÙ Level
     Ripple Counter  _³_     ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÙ              _³_

COMPONENTS
C1,2,4,7,9. 10n            R1,2,3,5,6,10,11,12,13,15,16. 390kê
C3. 10p                    R7,17,18,25. 10kê
C5. 47n                    R8. 1Mê
C6. 1n2                    R4,9,14,19,20,21. 47kê
C8. 4n7                    R22,23. 470ê
C10. 10uF                  R24. 100kê
D1-10 1N4148               VR1. 10kê
IC1 4017 Cmos Ripple       LED1 Red
IC2 4011 4x Cmos Nand      LED2 Yellow
T1,2,5. Small signal PNP   SW1 Double pole C/O
T3,4,6. Small signal NPN

HOW IT WORKS
The On/Off switch, switches power & also re-routes the PTT line via steering
diode D9 (in case the battery is flat). A light trickle charge for the battery
via R27 & D10 is taken off the PTT line when on Rx whether the unit is switched
on or off & is usuitable for dry cells.

When Mic PTT is low the LED1 lights via R22 & briefly pulses on T1 via C1 & R1
with C2 & R2 providing a power up pulse, T1 resets the ripple counter IC1 ready
for the 1st CW clock pulse. The Mic PTT low also turns on PTT drivers T5 via
R15 which turns on T6 via R17/18 to repeat the PTT condition to the Rig.

On release of the Mic PTT a long +ve pulse is feed into Gate A of IC2 via R7,
C7 & discharged by R8. This enables the oscillator IC2 Gate A & B. With C5 &
R10, R11 it oscillates around 27Hz which forms the "dot time" for the CW.

The CW CLOCK is filtered (kept clean on power up etc) with R5 & C3 to feed the
ripple counter IC1. The "Q0" pin 3 output line is low from 0-10 count & is used
to drive T5 via R16 for PTT as with the Mic while the "K" Pips are generated, &
it also drives T2 via R6 to maintain the long CW CLOCK gate ON pulse.

Ripple outputs "Q1" to "Q9" Pins 2 4 7 = dash, 10 = gap, 1 = dot, 5 = gap,
6 9 11 = dash, are diode gated D1-D7 & R9 to make up the timings for the "K".

The +ve CW signals control the AF oscillator in the same way as the CW CLOCK.
The AF oscillator is made from IC2 Gate C & D, & with the C6 & R12/13, it
oscillates around 1kHz.

The square wave AF output from IC2D drives T4 via R19 to light the LED2 via R23
to indicate "K" is going out, & also feeds the AF to the Butterworth filter
R20/21 & C7/8 to T3 emitter follower, to shape the tone to a near sine wave.
T3 is only biased on by the mean DC level of the TTL output when present. T3
feeds the output level setting pot VR1 which in turn feeds the K tones to the
Mic AF line via a DC blocking Cap C9 & a high value attenuator R24.

IN USE
This is not needed on FM as the squelch tail tells the end of overs quite well.
But for weak fading SSB signals or under heavy QRM it gives a very clear
unambiguous end of over that like all CW can be easily heard compaired to a
voice ending.

REPEATERS
Lots more letters are possible for repeaters etc. without going into the
complexity of computers & Pics etc. here with just a few more diodes & a pull
down R per letter. But don't use more that 2 diodes in series to get a letter.

Possible letters are... A,B,C,D,E,F,G,H,I,K,L,M,N,R,S,T,U,V,W,5.

Letters that are NOT possible are.. J,O,P,Q,X,Y,Z,1,2,3,4,6,7,8,9,0
B -...

 ÚÄÄÄÁÄÄÄÄÄÄÄ¿³
À³14 16 Q0  3³ÙÚÄ´>ÃÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ>H ....
ij13    Q1  2³ÄÙ Ú´>ÃÄÄ)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
ij15    Q2  4³ÄÄÄÁÄ´>ÃÄ)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄ)ÄÄ>D _..
 ³      Q3  7³Ä´>ÃÄÄÄÄÄÅÄÄÄÄÄ´>ÃÄÄÄÄÄÄ´  ³
 ³      Q4 10³ÄÄ´>ÃÄÄÄÄ)ÄÄÄÄÄÄÄÄÄÄÄÂÄÄ)ÄÄ)ÄÄ>L ._..
 ³IC1   Q5  1³Ä´>ÃÄÄÄÄÄÅÄÄÄ´>ÃÄÄÄÄÄ´  ³  ³
 ³      Q6  5³ÄÄ´>ÃÄÄÄÄ)ÄÄÄÄÄÄÄÄÂÄÄ)ÄÄ)ÄÄ)ÄÄ>U .._ 
 ³4017  Q7  6³Ä´>ÃÄÄÄÄÄÅÄÄ´>ÃÄÄÄ´  ³  ³  ³
 ³      Q8  9³ÄÄ´>ÃÄÂÄÄ)ÄÄÄÄÄÄÂÄ)ÄÄ)ÄÄ)ÄÄ)ÄÄ>K _._
 ³           ³Ú´>ÃÄÄ)ÄÄ)ÄÄÄÄÂÄ)Ä)ÄÄ)ÄÄ)ÄÄ´
 ³   8  Q9 11³ÁÄ´>ÃÄ´  ÃÄ´>ÃÙ ³ ³  ³  ³  ÃÄÄ>B _...
 ÀÄÄÄÂÄÄÄÄÄÄÄÙ      ³  ÃÄÄ´>ÃÄÙ ³  ³  ³  ³
                   RK  RH      RU  RL RD RB

A multi way logic selector etc, to select the letter before the AF osc to
give... No modulation = no CW, K = OK, B = On Battery Power. L= Low Mod,
H = High Mod, U = Freq Up, D = Freq Down, all depending on Modulation & FM
Discriminator DC output etc..


Why Don't U send an interesting bul?

73 De John, G8MNY @ GB7CIP





73's Danny

ÚÂÄÄ¿ ÚÂÄ¿  ÚÂÄ¿ ÚÂÄÄ¿ ÚÂÄ¿ ¿ Ú¿ ÚÄ NLD net bbs voor de regio Sneek.
ô    ÃÅÄÁ¿ ÀÁÄÅ´ ÀÁÄ¿ ô ³ ³ ÃÅÄÁ¿ 24 uur per dag QRV op Ch.24,34,38,40
ÀÁÄÄÙ ÀÁÄÄÙ ÀÄÄÁÙ ÀÄÄÁÙ ÀÙ ÀÄÙ ÀÙ  À CB:  NL2SNE@CB9SNK.FRL.NLD.EU 
                                     HAM: PD0SNK@PI8SNK.#FRL.NLD.EU


Lese vorherige Mail | Lese naechste Mail


 29.03.2024 03:36:21lZurueck Nach oben